What does Wi-Fi mean on a tablet? How to enter your wifi code into your tablet. How to set up a Wi-Fi connection on an Android tablet. Setting up a network connection via Wi-Fi

Any owner of a smartphone or tablet in most cases wants to use absolutely all their capabilities, including connecting to the Internet. In this regard, we have to decide how to connect the tablet to WiFi at home or connect to open or secure networks. To do this, you can use several basic options, which will be discussed.

How to connect a tablet to WiFi: basic methods

It’s no secret that absolutely all modern mobile devices have built-in modules that allow you to connect to wireless networks.

If we consider the question of how to connect a tablet to WiFi, for most devices you can use four main methods:

Connection via
Creating a connection through a distributing laptop or computer.
Using an external modem.
Establishing a connection through the services of a mobile operator.

How to connect a tablet to a WiFi router?

Connecting to wireless networks using a router seems to be the easiest. However, first you should check your router settings regarding automatic network configuration.

To do this, you need to log into the router's web interface by entering the combination 192.168.0.1 (or 1.1 for some router models) in the address bar of any Internet browser. Then you need to go to the DHCP configuration section. By default, automatic configuration is enabled, but you never know. Here, the location of the section or tab may differ depending on the router manufacturer. On the desired tab you just need to enable DHCP activation. In this case, you will not have to manually configure the tablet; the IP address will be assigned to the device automatically.

Next, you need to go to the tablet settings and activate the Wi-Fi connection by simply dragging the slider to the on position. A few seconds after activation, the built-in module will detect all wireless networks within range, after which all you have to do is select required connection and, if necessary, enter the security key.

In another case, when configuration needs to be done manually (with the router configuration element disabled), you should use the IP address value setting in the range from 192.168.1.2 to 1.254 (or from 0.2 to 0.254 - it all depends on what address the router initially uses for signal distribution).

For the DNS server, you can use either four eights, or two eights and two fours. The subnet mask is standard - four values 255 and a zero at the end.

Connection via laptop

Now let's see how to connect your tablet to WiFi via a laptop. In this case, you first need to configure the laptop so that it turns into a distribution device. Windows tools this, of course, can be done, but many users have to enter the settings network commands in the corresponding console causes legitimate difficulties. Therefore, it is better to use the installation of free automated utilities like Connectify or Virtual Router.

From the settings you will only have to enter the name of your network and access password. To connect to the newly created network, the same technique was used that was given to create a connection session through standard routers.

Establishing a connection using a 3G modem

To figure out how to connect your tablet to WiFi in this way, you will first have to purchase a modem compatible with the device and a special OTG cable through which you can connect any peripherals. Please note that this method is only suitable for Android devices (unfortunately, Apple devices do not support this technology).

Now you should start setting up. To set the necessary parameters, enter the data transfer section located in the main settings menu, after which the switch slider mobile traffic switch to the on position. Then we use Extra options(line “More”), select the APN access point. Now all that remains is to add it and enter the parameters received from the provider.

If you figure out how to connect a tablet (WiFi on ByFly, for example), setting the settings is very similar to the method of establishing a connection via a 3G modem. Only in this case, you need to pay attention to the fact that you must first establish a connection for the Wi-Fi module manually. The requested network may be hidden, so you need to use the SSID value in the parameters, select the security type and only then connect to the network.

Using the services of mobile operators

Finally, there is another way to solve the problem of how to connect your tablet to WiFi. Many modern devices support the installation of SIM cards, like on regular smartphones, with reference to the operator providing communication services.

Depending on the package, access is provided on a 3G or 4G network. Only in this case, the difference is that you can receive standard settings for Internet access from the operator or apply direct access by activating the data transfer module on mobile device(for example, for 3G+ networks). There is no need to configure anything here. The connection will be made automatically. But you need to pay attention to the provided traffic limit, since if it is exceeded, the operator may charge an additional fee.

Instead of a total

As can be seen from the above, none of the listed methods should cause difficulties when activating the connection. The only exception is setting parameters using Windows systems, but this technique was not specifically considered, since the use of special automated utilities in this regard looks much simpler and more attractive for the average user. In terms of preference for the chosen method, it all depends on the situation. But today there are routers in almost every cafe, so the easiest way to activate the connection is by launching the built-in Wi-Fi module directly on the tablet. If communication is required constantly, you will have to choose a connection through an operator (if installation of a SIM card is supported) or give preference to an external modem, but this costs money.

Quite a long time ago, digital devices entered our lives and became firmly entrenched in them, and wireless technologies contributed to the development of the market tablet computers. However, despite the rapid development information technologies, often inexperienced users ask how to connect a tablet to a router via a wireless Wi-Fi network. Since this issue is still on the surface for some users, I propose to examine it in detail in this publication. First of all, I recommend checking some parameters on the network device.

To do this, you need to find the DHCP automatic network configuration protocol and, if necessary, enable it. Thus, the DHCP server activated in the router will automatically assign an IP address to the tablet and save us from manual entry network parameter devices. Be sure to make sure that your Wi-Fi network is configured and activated. If you have no idea what network settings in question, I have given several examples below.

Checking the network parameters.

For example, in the interface ASUS router With new firmware ASUSWRT automatic network configuration protocol is located in the menu item " The local network» on the DHCP Server tab.

By default, Wi-Fi is enabled, but for an overview, the image shows the path to enable Wi-Fi in the interface.

Now let's look at the locations of these same settings on the TP-LINK router. So, the first thing you need to do is go to the “DHCP Settings” tab. As you understand, the function must be activated by specifying the start and end IP addresses.

Next, you need to make sure that the Wi-Fi wireless network is working. As a rule, by default this option is activated on the network device. Below I have presented an image with two pages that you need to pay attention to.

As you can see, the “Enable wireless broadcasting of the router” parameter is responsible for activating Wi-Fi in TP-LINK. In addition, do not forget to look at the “Wireless Protection” menu item and write down the password for accessing the Wi-Fi network. We checked the settings on the network device and activated DHCP so as not to manually register the IP address. Now all that remains is to connect the tablet to Wi-Fi router.

We connect the Android tablet to the Wi-Fi network.

Go to your tablet settings and enable Wi-Fi module. To do this, you just need to switch the slider to the ON position.

After this, the device will begin searching Wi-Fi networks and at the end will generate a list of available wireless networks.

In my case on this moment, he found only two wireless networks. A lock on the Wi-Fi signal indicates that both networks are locked with a password. Here you need to select the network that your router broadcasts. For me it is “Fast connect”.

In the window that opens, you need to enter the password (security key) for the Wi-Fi network that you specified in the wireless security settings and click the “Connect” button.

After this, authentication will be performed and the tablet will have access to the router’s Wi-Fi network. If configured, then you can already access the global network.

This is how easy and simple you can connect your tablet to a Wi-Fi router. I think you shouldn't have any difficulties. At the end of the article, let me remind you that if the DHCP function is disabled in the router settings, then the settings will need to be entered into the tablet manually. For example, register the IP address: 192.168.1.95; gateway: 192.168.1.1; DNS 8.8.8.8 or 8.8.4.4 (these are public server addresses for DNS queries from Google).

That is, if the router distributes a wireless network from the IP address 192.168.1.1, then the IP address of the device (tablet, smartphone) must be registered in the range from 192.168.1.2 to 192.168.1.254. The gateway on many routers or access points is usually 192.168.0.1 or 192.168.1.1. If you need to specify a network mask, then based on the specified ranges you need to enter 255.255.255.0. I hope everything is clear. As you can see, it is more convenient to connect automatically by enabling the DHCP network configuration protocol.

Must be connected to the Internet. Otherwise, its capabilities will be significantly limited, and the user will not be able to use it one hundred percent. In this material we will talk about how to connect your tablet to the Internet using WiFi router, built-in 3G module, external 3G modem, smartphone, laptop and even .

How to connect your tablet to the Internet via a WiFi router

If you have a WiFi router connected to the Internet and configured at home, then for you the most simple way Connecting your tablet to the Internet will use a wireless WiFi network. In order to do this you need to follow these steps.

Make sure your tablet has "airplane mode" turned off, or "airplane mode" as it's sometimes called. In this mode everything wireless connections do not work, so if it is turned on, you will not be able to use WiFi.

Open your tablet's settings and turn on the WiFi module (if it was disabled).

Go to the “WiFi” settings subsection. Here in the list of available WiFi networks you need to select a WiFi network from your router.

After WiFi selection network, you will only need to enter your login to access.

That's it, the process of connecting your tablet to the Internet is complete. If the WiFi router has access to the Internet, it will appear on the tablet.

How to connect a tablet to 3G mobile Internet

If your tablet is equipped with a built-in 3G module, then you can connect to mobile internet. First, you need to purchase a SIM card and insert it into a special compartment on the tablet. As a rule, this compartment is located on the side of the device.

After installing the SIM card, you need to enable the “Mobile Data” (or “Data Transfer”) function. As a rule, this is done in exactly the same way as on a regular smartphone. Usually, this is enough for the Internet to work on the tablet. If you have any connection problems, you can edit the APN access point settings.

To do this, you need to open the settings, go to the “More” section and open the “Mobile network” subsection.

After this, a small pop-up window will appear in which you need to select “Access Points (APN)”.

After this, you will only have to enter your operator's details.

How to connect a tablet to the Internet via a 3G modem

If your tablet does not have a built-in 3G module, then you can use external 3G modems. To do this, you will need a regular 3G modem, exactly the same one that is used to connect laptops, netbooks and desktop computers to the Internet.

Connecting a tablet to the Internet using an external 3G modem is a little more complicated and there can be a lot of difficulties. The first thing you need to do is set the 3G modem to Modem Only mode. To do this, you need to install the program on your PC. After that, connect your 3G modem to this PC, open the 3GSW program and activate the “Modem only” mode.

The PPP Widget application is required to set up a connection to mobile networks, since tablets without a built-in 3G module are not equipped with the necessary software. Open the PPP Widget application and enter the access point information, as well as your username and password. You can obtain this data from your mobile operator.

How to connect a tablet to the Internet via a smartphone

Another relatively simple way to connect a tablet to the Internet is to connect using a smartphone. To do this, you need to open the settings on your smartphone and go to the “Other networks” section.

After that, you need to open the “Modem and access point” subsection. In other shells, this subsection may be called differently, for example, “Modem mode and access point.”

That's it, after that your smartphone has turned into a Wifi access point. In order to connect your tablet to the Internet, simply connect to the Wifi network created by your smartphone. The Wifi network name, login and password can be found in the access point settings on your smartphone.

WiFi connection is the most convenient and in a fast way Internet connections for both smartphones and tablets. Naturally, a necessary condition For such a connection, you need to have a WiFi router. If you don’t have one, I recommend that you familiarize yourself with it.

The connection itself can be roughly divided into two stages: setting up the router and WiFi setup Internet on a tablet. However, before proceeding with the setup, just in case, I recommend checking the characteristics of both of your devices for compatibility. It is important to know that there are several modes WiFi connections, the most common at the moment are b, g and n. Accordingly, at a minimum, the same mode must be supported by both your router and tablet. Ideally, both your devices support n mode, this will give you the fastest data transfer speeds.

Setting up the router

We will look at the connection using the very common Dlink 320 router as an example. But you can use these instructions for other routers. Although their interface may differ quite significantly, the setup principle is exactly the same.

Log into your router's interface from your computer. To do this, open a browser on your computer and enter the IP address 192.168.1.1 in the address bar.
Enter the login admin and leave the password blank
In the router interface, find the Wireless Setup item and select Manual Wireless Connection Setup
Disable WiFi Protected Setup (WCN)
Enable the wireless network by checking Enable Wireless
In 802.11 Mode, select the wireless network mode that your tablet supports. (the same b, g, or n)
Enter the name of your network in the box Wireless Network Name (SSID)
In Wireless Security Mode, select WPA/WPA2
In the WPA/WPA2 settings, set the following values: Cipher Type – TKIP, PSK / EAP: PSK
Create an eight-digit password for your network and enter it in the Network Key section
Click Save Settings and reboot your router

Your router is now available for connecting mobile devices.

Setting up the Internet on a tablet

Enter the tablet settings from the application menu or by clicking on the corresponding icon in the lower right corner of the screen
In the “Wireless Networks” section, turn on WiFi by moving the corresponding slider.
After turning it on, a list of available WiFi networks will appear on the right side of the window. Select your router's network. The network name will be the one you specified in the router settings.
In the window that appears, enter the password that you specified in the router settings and click connect.

After this, your tablet is ready to work on the Internet, and when you reconnect, you will no longer need to enter a password because it will be stored in the device memory by default.

One of the capabilities that almost all tablets have is an Internet connection: you can learn more about this from the article. Equally important is your device's ability to connect to a Wi-Fi network. It is this point in mastering a new gadget that most often causes the greatest difficulties, and we will dwell on it in more detail.

How to set up Wi-Fi on an Android tablet

To set up Wi-Fi on Android tablet, follow these simple steps:

In the tablet settings, turn on the Wi-Fi receiver. To do this, select “Wireless Networks” in the settings menu, and then click on the “Wi-Fi” line.
After this, a list of wireless networks available for connection should appear on the screen of your tablet. From them, select the one you need to connect to, and the system will prompt you to enter the network password in the appropriate window.

Most often, no further manipulations are required, and you can use your tablet for your own pleasure. However, if there is a need to further configure the connection, follow the instructions below.

To access the network settings settings, hold down its name for a few seconds, and when the system prompts you to select an action for this network, select “Change network.”
Next you will see the settings panel. To configure settings such as gateway, IP address and DNS server addresses, select “Advanced”. In the window that opens, enter the data that was provided to you by your Internet provider in the appropriate lines.

As a rule, there is no need to use the last two points indicated, since the Android OS has a function automatic settings networks and determining its parameters.

How to set up Wi-Fi on an iOS tablet

If you still don't know how to make Wi-Fi on your tablet iOS reality, follow these steps:

Open the "Settings" menu and select the "Wi-Fi" line. A window will open, the first line of which will read “Wi-Fi” and a switch. Set the switch to on and your tablet will start searching available networks.
When the search is completed, a list of available networks will appear below the line, and you will be asked to select one of them to connect to. Select the desired network, enter (if required) the network access key in the window that appears and click “Connect”.
If the connection is successful, an indicator will appear in the upper left corner Wi-Fi signal networks. To configure a network, click on the arrow to the right of the network name. You will be taken to the Advanced Settings window where you will be asked to enter the IP Address, Default Gateway, and DNS Address values.

In addition to Wi-Fi connections, many tablets allow connections to the 3G network. To learn more about this, please refer to the article