Printer Firmware Instructions Xerox Phaser 3260DI, 3260DNI, 3052NI

To order the firmware, you will need the following data:

• Model of the device (written on the case);
• Serial number(S/N);
• CRUM chip cartridge;
• Firmware version.

You can find this data by printing the "Configuration report" and " Expendable materials"(Supplies report).

Enter the data obtained from the reports into the "Order Form" in the right column of this page and click the "Order" button.

Printing reportsXerox Phaser 3260DI, 3260DNI, 3052NI

Print configuration report:

In standby mode, press and hold the [ STOP ] button for about 4 seconds (until the status indicator flashes quickly), release the button.

Printing the Supplies Information Report:

press and hold the [ STOP ] button for about 6 seconds (until the status indicator lights up steadily), release the button.

In case of complete blockage, to print a report, replace the chip in the cartridge with an original working one.

Firmware versions and their compatibility

Firmware Phaser 3260DI, 3260DNI Phaser 3052NI

In the archive

Instructions for firmware MFP Phaser 3260DI, 3260DNI Phaser 3052NI

1 Flash the printer with original firmware

Download and unzip the archive with the original firmware (link to the archive with the original firmware at the bottom of the right column of this page). After that, enter the printer into forced download mode. Wait automatic installation forced mode drivers. Then drag the firmware file PH3260_V3.50.01.08.hd to usbprns2.exe with the mouse. A black console window with running dots will appear and close after a few seconds. After that, the printer will start flashing. Wait for the printer to restart. After rebooting the printer, we proceed to install the FIX firmware.

2. We flash the device with the first firmware fix file

In ready mode, drag the first firmware file First_PH3260_V3.50.01.08.hd to usbprns2.exe with the mouse

A console with running dots will appear, which will close after a few seconds. After that, the device will start flashing

Wait for it to reboot. After the reboot, we proceed to the next stage of the firmware.

3. Flash the device with the second firmware fix file

Before this flashing step, you need to enter the printer into forced download mode.

Move the second FIX firmware file FIX_NU_xxxxxxxxxx_PH3260_V3.50.01.08.hd to usbprns2.exe with the mouse. A black window with running dots will appear and close after a few seconds. After that, the device will start flashing. Wait for the printer or MFP to restart.

4 Seal the chip contacts on the cartridge or remove the chip

After the reboot, remove the chip and do not allow the installation of other chips! The toner level will always show 100%.

Attention! For these MFP models, it is recommended to update the firmware from the ready mode.

Entry into forced mode!

With the printer turned off, press and hold the [ STOP ] button. Press and hold the [POWER] button, after ~ 1-2 seconds, release both buttons. Upon successful entry into forced mode, the status indicator should turn orange (the other indicators will also be on).

After the reboot, the printer will already work without a chip on the cartridge.

Printer firmware (firmware) is the setting software printer with a fixed code that resets the counter of printed pages and prevents the printer from blocking.

Crypto protection (in other words, protection against refueling) installed in modern Samsung and Xerox devices counts down the specified value by the formatter program code (shown in the picture), the number of pages printed, after which the printer is blocked and until you install a new cartridge or flash your printer, it will not work. The firmware of the device is done without opening and other actions aimed at violating the integrity, the printer is entered into the service mode, after which the "FIX" is uploaded via USB.
On the issue manufacturer's warranty. If you are worried that in the event of a printer breakdown you will not be able to contact the warranty workshop, we want to reassure you, let's say your paper pickup roller is broken, you are going to carry the printer or MFP to the service, you can return firmware firmware for the period of repair in the warranty workshop of the manufacturer or seller. Many of our customers turn to the warranty service and save a lot on refilling cartridges. Let's try to calculate the savings on the example of one printer... well, for example Samsung ML-1660. Now many are wondering "What is printer firmware?".

An average-sized office buys a new cartridge (2240 ​​rubles) about once a month. Refilling the cartridge (350 rubles) is also required approximately once a month. The printer will last approximately 4 years or 48 months.
2240 rub. x 48 months = 107520 rub. This is an approximate cost for the purchase of cartridges for 4 years (WOW!!!..........)
350 rub. cartridge refill x 48 months =16800 rub. refueling expense for 4 years + 1000 rubles. (firmware) = 17800 rubles.
Thus, an exemplary saving for 4 years will be89720 rubles, (it's over, this is a rough calculation, during this time you will have to buy several cartridges since the physical resource is limited) and this is on 1 printer, and now think, do office equipment manufacturers not want to lose that kind of money from users of their printers and MFPs? Of course, Samsung and Xerox are against refilling cartridges in any form, the fight against refillers continues until the economy wins, we'll see what happens next.

Our services:

• Estimated prices for services

  Name of works	b/w f. A4 up to 16 ppm	b/w f. A3 up to 16 ppm	b/w f. A3 16-24 ppm	b/w f. A3 25 - 39 ppm	b/w f. A3 40-59 ppm
  Departure of an engineer within the Moscow Ring Road	1000	1000	1000	1000	1000
  Departure of an engineer outside the Moscow Ring Road	according to the agreements	according to the agreements	according to the agreements	according to the agreements	according to the agreements
  Diagnostics (paid in case of refusal to repair)	300	360	500	700	1000
  Prevention	850	1020	1100	1450	1850
  Resetting error codes	200	240	200	250	300
  Replacing Paper Feed/Original Parts	750	900	950	1100	1200
  Paper/Original Feed Unit Repair	850	1020	1000	1200	1300
  Replacing Paper Transport Parts	700	840	800	900	1000
  Paper transport unit repair	800	960	900	1000	1100
  Replacing the drum unit and squeegee	800	960	1100	1300	1600
  Replacing the Teflon Roll	600	720	850	950	1050
  Tefl bearing replacement shaft	300	360	350	400	450
  Replacement rubber shaft	650	780	700	950	1050
  Replacing rubber shaft bearings	300	360	400	400	450
  Felt roller replacement	400	480	450	450	500
  Thermal film replacement	750	900	950	1200	1400
  Fuser Replacement	750	900	950	1200	1400
  Coronator/Charge Roller Repair	400	480	500	600	800
  Change of developer	500	600	550	600	700
  Removing the electronic component a (boards)	250	300	300	500	650
  Repair of electronic component a (boards)	800	960	1000	1200	1400
  Removing the Drive Assembly	200	240	450	500	700
  Drive Unit Repair	750	900	1000	1200	1500
  Repair of mechanical components	700	840	900	1000	1300
  Function block replacement	700	840	900	1100	1300
  Scanner Assembly Repair	800	960	1000	1200	1300
  Adjustment-calibration of the scanner assembly	600	720	800	900	1100

The Xerox Phaser 3052NI printer, which uses Laser B/W printing technology with a maximum paper size of A4, a print resolution of 600*600 and a print speed of up to 26 ppm. pages per minute, its use in small and medium-sized companies, at home, given the small amount of printing, has proven itself well in terms of quality and the possibility of refilling cartridges.

The starter cartridge is designed for 600-700 pages (this is the starter - trial cartridge) at which time the Xerox Phaser 3052NI Printer indicates that the toner cartridge is running low, and you need to buy and install a new one. But here there is a choice - buy a new cartridge or refill an empty one. If you choose the second option, a certain problem appears, namely: a microcircuit (chip) is built into the cartridges for this printer, it transmits information about the remaining toner in the cartridge hopper to the machine. And if you are refilling a cartridge, it is not enough to fill it with toner, you need to remove crypto protection from the chip (block the count of printed pages).

Here again, there are two options for solving the problem - change the chip in the cartridge or the printer firmware (software change) in the printer. Replacing the chip is an expensive pleasure, since the chip has to be changed every time the cartridges are refilled, this is the main disadvantage of the replacement. The second one is much more profitable and less problematic than the constant replacement of the chip - the Xerox Phaser 3052NI printer is reflashed once and for all.

Firmware for the Xerox Phaser 3052NI printer is performed both in our workshop (1-2 hours in time) and in the client's office. The customer must have a computer (laptop) with operating system Windows and an Internet connection.

To make firmware for your device, the following initial data is required:

• device model (indicated on its case);
• serial number - (10 characters) - specified in the Configuration Report;
• firmware version - indicated in the Configuration Report;
• CRUM chip toner cartridge- (11 characters) is listed on the Supplies Information report under Toner Information. Not to be confused with CRUM Imaging Unit from the same report

This data can be obtained by printing two reports on your printer: Configuration Report and Supplies Information (Configuration and Consumables).

1. Printing reports

ATTENTION!!! Report printing is possible on an unlocked printer!

To unlock it, you need to replace the chip in the cartridge with an original working one.

If the printer is locked, firmware order data can be obtained using the PC_INFO_TOOL utility. You can download the utility for free in our file archive, in the section - Soft

To print a Configuration report:
press and hold the [ WPS ] button for about 10 seconds (the status indicator will blink, then stay on, then start blinking again). Release the button.

To print the Supplies Information report:
press and hold the [ WPS ] button for about 15 seconds (until the status indicator lights up again). Release the button.

Sample Configuration Report - opens in a new window

Supplies Information Sample Report - opens in a new window

2. Preparation for the firmware.

Connect the printer to computer USB cable and install the necessary drivers. The cable should be as short as possible.

Disconnect all unnecessary hardware from the computer.

Close all programs.

Connect the printer to the power supply and make sure the connection is secure.

Important!!! Power interruption during flashing will damage the device.

ATTENTION!!! Flash with a chip on the cartridge. The chip on the cartridge must be the one whose CRUM is specified in the order for the firmware. Another chip - another firmware.

3. Firmware order

Select the firmware property yourself: U - without update protection or NU - with update protection. ()

Click the "Submit" button.

If you entered your email address correctly. mail, you will receive an email with a link to download the archive with the firmware and further instructions.

4. Printer Firmware:

Unpack the resulting two archives into a separate folder. The Fix-firmware package includes 4 files:

1. patch (PH3052_V3.50.01.xx.hd)
2. 2 firmware files ( First, FIX);
3. bootloader (usbprns2.exe);
4. reedme.txt file;

The procedure for downloading firmware files to the device:

1. patch (PH3052_V3.50.01.xx.hd) - in forced mode
2. first (First_**********_ Phaser3052 V3.50.01.xx.hd) -in ready mode;
3. the second (FIX _ ********** _ Second Phaser3052 V3.50.01.xx.hd) - in forced mode.

What is printer firmware?

The printer firmware is an update of the software version, reset - zeroing the counter printer.

Why is it necessary to flash the device?

It is necessary to flash the printer if you have run out of a cartridge and you decide to refill it. but
refilling the cartridge is not profitable for the printer manufacturer, so he installs a CRUM chip (complex
crypto-protected microchip), which will block the operation of a refilled cartridge. Can buy
new cartridge. But it is more profitable to flash the printer once and refill the cartridge without problems.

How to find out the serial number of the device, firmware version and CRUM-chip?

All printer firmware data can be obtained by printing configuration and consumables reports.

Firmware Version (OS Version)- current printer firmware version
Mashihes Serial Number- serial number of the device
serial no.- CRUM chip number

Configuration report example:

Consumables report example:

Can the master come to the client's office to flash the printer?

You can call the master to the office, to your home or bring the device to us at your own service center.

How long does it take to flash a printer?

The procedure for flashing the printer itself does not last long and takes 15-20 minutes.

Can I use a new cartridge after flashing?

Yes, but when installing a new cartridge in the device, you must remove or seal the chip with adhesive tape.

How many times can a cartridge be refilled?

The laser type cartridge can be refilled 3-4 times. Over time, the internal parts of the cartridge wear out.
and they need to be changed. Proper operation plays a significant role in the number of cartridge refills.
cartridge, the quality of the toner used, and the method of refilling. High-quality refueling takes place in a specially
equipped room, with complete disassembly and cleaning of all parts of the cartridge.

How long does a refilled cartridge last?

Each cartridge has its own print yield (number of pages). For example: HP Q2612A cartridge yield
is 2,000 sheets. The manufacturer has determined that this resource is designed for 5% filling of the sheet.
This is a small amount of filling the document. In practice, the text on the sheet is more than 5%, respectively, the cartridge
enough for a smaller amount declared by the manufacturer. Conclusion, cartridge yield depends on what you print.
and with what volume of filling on the sheet. The new device is sold with a starter cartridge. Its resource is approximately
30-40% and it is intended to demonstrate the performance of the printer.

What is the warranty for printer firmware?

All the firmware we use are prepared individually for each device and undergo a mandatory
check. We guarantee that the printer firmware will not affect the performance of the device itself.

* What is a chip and why is it needed?

Answer: Chip - This is a memory chip that stores a number of information necessary for the operation of the printer.
For example: manufacturer, cartridge type, date and time of manufacture, activation date, amount spent
toner, etc. The shape of the chips resembles a thin plate.

Version V3.50.01.05 V3.50.01.11

Firmware for printers xerox phaser 3050, 3052NI

Xerox Phaser 3052/3052NI Printer Firmware

On the this moment version available v3.50.01.05 v3.50.01.11

Price 500 rubles

To order firmware Xerox Phaser 3052/ 3052NI the following information is required:

• 1). exact model printer (as written on the Xerox Phaser 3052/3052NI printer)
• 2). Printer firmware version (in the Configuration Report, see Firmware Version, example v3.50.01.05)
• 3). Printer serial number (on the Configuration Report, see Machine Serial Number, 10 digits)
• 4). CRUM chip number of the black cartridge (on the Supplies Information Report, see Serial No: CRUM, 11 digits)

How to print a Xerox Phaser 3052/ 3052NI report

To print the configuration report: press and hold the [ STOP ] button for about 10 seconds (until the STATUS indicator starts blinking), release the button.

To print the Supplies Information report: press and hold the [ STOP ] button for about 15 seconds (until the STATUS indicator lights up steadily), release the button.

Printer does not print reports

Very often we are faced with the fact that the printer does not print the reports we need, the cartridge has exhausted its resource, the printer is blocked, in order to find out the version, serial, crum number, we have special program with which you can find out all the necessary data.

Printer Firmware Instructions Xerox Phaser 3052/ 3052NI

With the printer off, press and hold the button<< STOP >> at the same time turn on the printer without releasing the button<< STOP >> Exactly 3-5 seconds after that, release the button<< STOP >>. The printer is ready for the firmware update procedure in forced mode.

Warning: Flash with a chip in the cartridge! Crum number is the chip!

Before flashing, make sure that the printer is connected to the computer and identified by the computer! after everything has been checked, you only need to flash the printer according to the instructions, (We send the instructions with the firmware),

wait until the printer reboots, then remove the cartridge from the printer and remove the chip or seal it with tape.

insert the cartridge, install the paper in the sheet tray five, the indicator should turn green.

Find out information about the printer if the printer does not print a report (CRUM number, Firmware version).